- Installation Tips
Step #1: Cleaning
A. Wash and dry hands to remove oils and dirt.
B. Clean the device and screen with provided wet and dry wipes.
Grasp the Step 1 tab to remove the protective film layer. **Do not touch the adhesive side once the protective film layer is removed.
Ensure that the adhesive side of the screen protector is facing down. With your fingertips, carefully hold two tab on either end of the screen protector.
Using the tabs, carefully align the screen protector with the tablet. Now slowly lower the screen protector onto your device.
Once the screen protector is in place lightly press the center of the screen protector and then gently slide your fingertip across the screen, allowing the screen protector to adhere itself to the tablet.
Eliminate any bubbles by using the included Squeeze Card to push bubbles out.
Finally hold one of the two tabs and slowly peel back the second protective plastic film.
Use our tips below to help achieve the best results during installation . . .
Each screen protector consists of 3 layers of film. The front and back film layers are protective, mask films (where the Step 1 and Step 2 stickers are affixed) and are used for packaging/shipping purposes ONLY. The actual screen protector for your device is the film in the middle. Please use the stickers like "handles" to assist you in in grasping and removing the mask film layers. DO NOT remove the actual stickers themselves. Discard the 2 outer protective film layers after installation.
Installation should always be done with your device turned off and in a well-lit, dust-free, environment. Consider doing your installation in the bathroom after a hot shower. The humidity will keep dust particles to a minimum and allow for optimal installation conditions.
The included dust removal stickers can be used to remove dust from the screen and the adhesive side of the screen protector. To use, simply touch the adhesive side of the sticker onto the dust and, as you remove the sticker, the dust will also be removed.
And remember … don’t stress out over the installation process! If you have any difficulty, or damage the product during installation, we have you covered under our Lifetime Guarantee. Contact us and we will send you a free replacement so you can “give it another go”!
Q1. “This is my first time putting on a screen protector and I tried my best to install it properly, but I was unable to remove all of the bubbles during the installation of the first protector. What do you recommend?”
A. We highly recommend the “Rubber Band Hinge Method” of installation (above) for any beginners, or for anyone having difficulty installing their screen protectors. You can view a demonstration of this method at the top of this Installation Page. In the meantime, please try using this method to help install the second, “back-up” screen protector that is included in the package. Also, you may contact us at email@example.com to receive a replacement to “give it another go” or if you need further assistance with installation.
Q2. “My screen protectors just arrived and when I opened them up they have a crease in the middle of them. What happened and what should I do?”
A. We apologize for any inconvenience this has caused. It seems as if your protector may have been damaged during shipping. Please contact us at firstname.lastname@example.org to receive a free replacement item, compliments of our hassle-free, lifetime replacement warranty on all screen protectors.
Q3. “I put my screen protector on and now the display screen of my device is not looking as clear. What can I do to fix this problem?”
A. It is possible that the reason for this 'cloudy' appearance is due to the fact that you have purchased the Anti-Glare version of our screen protectors. In order to be effective at reducing glare and fingerprints, these protectors are made with a clear, matte material and can produce a slight pixilation of the devices’ screen clarity. This is the natural effect created by the matte (anti-glare) frosted texture and you may be more satisfied in purchasing one of our HD Clear screen protectors.
Q4. “I put on my new screen protector and now I cannot scroll as easily as before, why?”
A. We assure you that our screen protectors are made of the highest quality PET Materials on the market and are designed to be as thin as possible, yet still retain maximum scratch resistance. At times it is possible to experience some initial resistance scrolling when the screen protector is first applied. If you “break it in” and continue to have problems with the scrolling/motion, it is possible that you may have received a defective product. Please email us at email@example.com and we will be more than happy to help solve this matter.